Updates to setup script. Add new config_phaser.txt.

cn0566-config.txt

@@ -21,8 +21,8 @@
 hdmi_force_hotplug=1
 
 # uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
+hdmi_group=2
+hdmi_mode=82
 
 # uncomment to force a HDMI mode rather than DVI. This can make audio work in
 # DMT (computer monitor) modes
@@ -59,7 +59,7 @@ camera_auto_detect=1
 display_auto_detect=1
 
 # Enable DRM VC4 V3D driver
-dtoverlay=vc4-kms-v3d
+# dtoverlay=vc4-kms-v3d
 max_framebuffers=2
 
 # Disable compensation for displays with overscan
@@ -81,8 +81,13 @@ arm_boost=1
 
 # Phaser board overlay:
 dtoverlay=rpi-cn0566
+#dtoverlay=rpi-cn0566_no_ad7291
+#dtoverlay=rpi-cn0566_no_gpio
+#dtoverlay=rpi-cn0566_minimal
+
 
 # Heartbeat blinky:
+dtparam=act_led_gpio=26
 dtparam=act_led_trigger=heartbeat
 
 # Short GPIO121 (pin 40) to ground for shutdown:

config_cn0566.txt

@@ -87,6 +87,7 @@ dtoverlay=rpi-cn0566
 
 
 # Heartbeat blinky:
+dtparam=act_led_gpio=26
 dtparam=act_led_trigger=heartbeat
 
 # Short GPIO121 (pin 40) to ground for shutdown:

config_phaser.txt

@@ -0,0 +1,94 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+hdmi_group=2
+hdmi_mode=82
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+# Automatically load overlays for detected cameras
+camera_auto_detect=1
+
+# Automatically load overlays for detected DSI displays
+display_auto_detect=1
+
+# Enable DRM VC4 V3D driver
+# dtoverlay=vc4-kms-v3d
+max_framebuffers=2
+
+# Disable compensation for displays with overscan
+disable_overscan=1
+
+[cm4]
+# Enable host mode on the 2711 built-in XHCI USB controller.
+# This line should be removed if the legacy DWC2 controller is required
+# (e.g. for USB device mode) or if USB support is not required.
+otg_mode=1
+
+[all]
+
+[pi4]
+# Run as fast as firmware / board allows
+arm_boost=1
+
+[all]
+
+# Phaser board overlay:
+dtoverlay=rpi-cn0566
+#dtoverlay=rpi-cn0566_no_ad7291
+#dtoverlay=rpi-cn0566_no_gpio
+#dtoverlay=rpi-cn0566_minimal
+
+
+# Heartbeat blinky:
+dtparam=act_led_gpio=26
+dtparam=act_led_trigger=heartbeat
+
+# Short GPIO121 (pin 40) to ground for shutdown:
+dtoverlay=gpio-shutdown,gpio_pin=21,active_low=1,gpiopull=up