Skip to content

Commit

Permalink
hpm sdk release v1.7.0
Browse files Browse the repository at this point in the history 
[1.7.0] - 2024-09-30:

Main changes since 1.6.0
Tested Segger Embedded Studio Version: 8.16a
Tested Zcc toolchain 3.2.4

- Changed:
  - soc: HPM6E00: HPM6E80: add tsw section
  - soc: add hpm_otp_table.h
  - soc: enet: add a macro for DMA bus width
  - soc: system.c: set bpor.por_confing retention bit to avoid bgpr data loss
  - soc: pcfg: add pcfg_wakeup_src_t enum and pcfg_update_periph_clock_mode API
  - soc: hpm5300: exclude fgpio region from dlm
  - soc: add CONFIG_ENABLE_BPOR_RETENTION macro to control bpor retention
  - soc: linker: icf: update cherryusb_usbh_class_info section placement
  - soc: HPM6300/HPM6700: delete pcfg_dcdc_set_current_hys_range() API
  - ip: i2s: add and use clk_i2s_src_audn instead of clk_i2s_src_aud0/1/2/3
  - boards: remove hpm6750evk support
  - boards: hpm6e00evk: update femc pinmux
  - boards: pinmux: set max frequency slew rate for SPI GPIO
  - boards: hpm5301evklite: Change cap1 and comp1 pins of gptmr0
  - boards: hpm5301evklite: change i2c2 to i2c3 for BOARD_APP_I2C
  - boards: add board_init_gptmr_channel_pin API for all board
  - boards: hpm6e00evk: update core1 debugger console readme
  - boards: all: add board_init_acmp_pins API
  - boards: hpm6800evk: adc16: update clock bus name for clock initialization
  - boards: adc16: rename api parameter clk_src_ahb to clk_src_bus
  - boards: add BOARD_APP_ADC16_CLK_BUS definition
  - boards: hpm6e00evk: update board readme
  - boards: hpm6e00evk: bump up DCDC voltage to 1250mv
  - boards: add enet pps input feature and pinmux setting API
  - boards: add missing board feature and pin descriptions for enet pps output pin
  - boards: xxxx.yaml: rename board feature name related to enet pps pin
  - boards: add BOARD_MASTER_I2S and BOARD_SLAVE_I2S
  - boards: add board mic and speaker i2s definition
  - boards: doc: pwm: add pwm pin descriptions.
  - boards: hpm6800evk reduce ddr io leakage.
  - boards: hpm6800evk: pps: adjust pinmux settings
  - drivers: tsw: optimize the logic of sending and receiving APIs
  - drivers: tsw: add APIs for speed, interface, and clock delay settings
  - drivers: tsw: split tsw_ep_enable_mac_ctrl API to two APIs for enableing and disabling
  - drivers: usb: update usb phy init for suspend
  - drivers: qeiv2: update comments
  - drivers: i2c: auto ack needs to be enabled after the transmission is completed for i2c_master_transfer API
  - drivers: adc16: split adc16_set_pmt_queue_enable() into enable and disable API
  - drivers: gptmr: add opmode cntmode monitor configuration member for gptmr_channel_config API
  - drivers: spi: add the judgment that the frequency ratio cannot be greater than 510 for spi_master_timing_init API
  - drivers: enet: add retry logic in DMA initialization
  - drivers: spi: Add slave mode judgment for spi_control_init API
  - drivers: spi: add spi busy state judement for transfer APIs
  - drivers: uart: add disable rx timeout trigger dma function
  - drivers: i2s: add buff data align with frame feature
  - drivers: acmp: add acmp_channel_config_cap_selection
  - drivers: acmp: update acmp_channel_config_dac API
  - drivers: usb: update usb phy init and deinit
  - drivers: enet: add auxiliary snapshot APIs and struct definitions
  - drivers: usb: update usb_force_port_resume() annd add usb_hcd_disable_ase_pse() APIs
  - drivers: tsw: update the prefix of apis starting with tsn to tsw
  - drivers: qeiv2: update qeiv2_config_adcx_adcy_param()
  - drivers: usb: update usb_hcd_disable_ase_pse() & usb_hcd_enable_ase_pse()
  - components: enet_phy: rtl8211: optimize logic for initialization config
  - components: ppi: add assert check for cs_index and cmd_start_index
  - components: ppi: update AD-MUX mode config to decrease address latch
  - components: smbus:  i2c_master_write replaces i2c_master_transfer for all smbus write APIs
  - components: serial_nor: Added configuration return judgment for transfer API
  - components: serial_nor: judge DMA sending completion for hpm_spi_transfer_via_dma API
  - components: spi: add spi busy state judgment for hpm_spi_transfer_init API
  - components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_buffer_nonblocking API
  - components: i2s_over_spi: optimized hpm_i2s_master_over_spi_tx_stop API
  - components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_is_busy API
  - middleware: hpm_math: support zcc new version
  - middleware: cherryusb: update to v1.4.0
  - middleware: lwip: CMakeLists.txt: add cmake flag for apps
  - middleware: cherryusb: don't clean csc bit when init
  - middleware: cherryusb: msc host: support multi msc device
  - middleware: fatfs: cherryusb: support two msc device
  - middleware: reduce netx mem usage
  - middleware: cherryusb: host: update usb_hc_deinit()
  - middleware: usbx: host: delete mode setting in usb_host_mode_init()
  - middleware: hpm_sdmmc: sdcard: added retransmission to improve SPI SD card compatibility
  - middleware: tinyengine: rename old function
  - samples: audio_codec: change default codec setting in CMakeLists.txt
  - samples: adc16 & motor_ctrl: update adc16 preemption queue enable control APIs
  - samples: ppi: parallel_adc: update function name
  - samples: ppi: async_sram: update to support AD Mux Mode
  - samples: lwip & modbus: add judgement for the return value of enet controller initialization
  - samples: lwip: lwip_iperf: exclude flahsh_uf2 & flash_uf2_release targets
  - samples: lwip: add conditional compilation for RMII port
  - samples: cherryusb: msc host: adapter to fatfs update
  - samples: drivers: acmp: replace init_acmp_pins API with board_init_acmp_pins API
  - samples: ecat: read mailbox ram buff by ram alias address
  - samples: ecat: set PHY offset
  - samples: ecat_phy: disable PHY addr 00 broadcast response
  - samples: drivers: adc16: reference APP_ADC16_CLOCK_BUS instead of clk_adc_src_ahb0
  - samples: ecat_io: update flash_eeprom data address
  - samples: ecat: update SSC config xml and ESI xml
  - samples: lwip: ports: rtthread-nano: single&multiple: add sys_arch_protech()/sys_arch_unprotect()
  - samples: power_mode_switch: move sysctl_enable_cpu0_wakeup_source_with_irq() to stop mode settings
  - samples: power_mode_switch: keep puart clock and wakeup enable visible
  - samples: acmp: add a macro TEST_ACMP_DAC_MAX_VALUE for better compatibility
  - samples: drivers: enet: pps: app.yaml: rename dependency
  - samples: ppi: parallel_adc: use macro BOARD_PPI_ADC_CS_INDEX
  - samples: i2s: use BOARD_MASTER_I2S and BOARD_SLAVE_I2S
  - samples: audio_codec: use board speaker macros
  - samples: cherryusb: audio: use board mic and speaker macros
  - samples: lwip & cherryusb/host/usbnet: use the external struct timeval definition from compile system
  - samples: esc: update esc read to 32bit access
  - samples: ecat_foe: update log and README
  - samples: ecat_foe: foe flash read cache maintenance
  - samples: ppi: use macros to select pins
  - samples: drivers: gptmr: cntmode: volatile to key parameter variables to prevent them from being optimized
  - samples: spi_sdcard: Added delay function registration
  - samples: cherryusb: mouse_wakeup: update printf log
  - samples: cherryusb: midi: update readme
  - samples: i2s: change HDMA to XDMA
  - samples: tflm: optimized speed.
  - samples: tflm: add zcc compile options.
  - samples: spi_component: full_duplex: Add known issues in the master readme
  - samples: spi_components: half_duplex: reduce SPI SCLK frequency to adapt to different slave boards
  - samples: spi_components: full_duplex: reduce SPI SCLK frequency to adapt to different slave boards

- Fixed:
  - soc: HPM6800: HPM6880: fix the clock bus name for wdg
  - soc: SPI_SOC_TRANSFER_COUNT_MAX Definition error for HPM6E00
  - soc: preserve kept symbols while -flto is enabled
  - soc: hpm6880: fix clk bus name for adc from ahb0 to axis0
  - soc: HPM6300: fix get get_frequency_for_i2s_or_adc() problem
  - soc: HPM6700: fix clock_set_i2s_source() check condition
  - soc: romapi: Fix unexpected data fetch error during flash init/write.
  - soc: linker: gcc: fix fast_ram postion
  - boards: hpm5301evklite: add a missing macro BOARD_APP_ADC16_CLK_BUS
  - boards: i2c init: clock_add_to_group() should be before board_i2c_bus_clear()
  - boards: hpm6800evk pinmux PRS set wrong value
  - boards: hpm6750evkmini: fixed the iomux errata causes the slave to not work issue
  - boards: hpm6750evk2: fixed the iomux errata causes the slave to not work issue
  - boards: hpm6750evkmini: add the missing implement of enabling enet irq
  - boards: hpm6750evkmini: fix touch reset timing.
  - drivers: i2c: correct API name
  - drivers: gptmr: fix cmp value can't set 0xFFFFFFFF problem
  - drivers: pwmv2: fix counter burst set error.
  - drivers: enet: fix return value of enet_dma_init()
  - drivers: usb: fix usb_dcd_remote_wakeup() api
  - drivers: enet: fix enet max frame size
  - drivers: spi: Fixed mode variable assignment error for spi_slave_get_default_format_config API
  - drivers: i2s: fix fill dummy data in slave mode
  - drivers: adc16: fix ADC16 conversion results in single-ended mode
  - drivers: enet: fix that TSIS interrupt is disabled by default
  - drivers: femc: fix cmd_data_width comment error
  - drivers: spi: fixed offset digit error problem for spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
  - drivers: spi: fixed possible packet loss during reception for spi_read_data API
  - drivers: usb: fix phy init for host
  - drivers: touch: gtxx: fix reset timing
  - drivers: mipi dsi: fix bandwidth low
  - drivers: mcan: fix wrong offset in can_rx_message_t.
  - drivers: adc12: fix using a wrong calibration value
  - components: ppi: fix config variable init value
  - components: serial_nor: Fixed the nonblock APIs naming error
  - components: serial_nor: spi: fixed formating issue for write API
  - components: eeprom_emulation, add "fence.i" after nor_flash init
  - components: spi: fixed the waring of no return value for hpm_spi_transfer_init API
  - middleware: fix Nan calculation error.
  - middleware: lwip: apps: lwiperf: fix the type of clk_id from int to clockid_t
  - middleware: fix tickless mode cannot work
  - middleware: eclipse_threadx: netxduo: fix confilicting types for 'enet_mask_interrupt_event'
  - middleware: tinyengine: zcc compile error.
  - middleware: cherryusb: fix msc class miss return
  - middleware: motor_monitor: fix nds toolchain error
  - middleware: hpm_mcl: pwm output exception.
  - samples: sdm: correct gptmr trigger time
  - samples: gptmr: cmp0 and cmp1 should be setting together
  - samples: i2s_emulation: fixed playback is not actually stopped issue
  - samples: pwmv2: fix pwm period error.
  - samples: drivers: dac: fix output stop after restart in buffer mode
  - samples: fatfs: fix driver_num_buf don't have EOF
  - samples: dac: buffer mode: fix DAC output of negative narrow pulse nearly to zero at the top of sinewave
  - samples: lwip: fix enet receive buffer size setting
  - samples: lwip: fix some memroy-related issues when using socket/netcon API
  - samples: cherryusb: audio: fix mute problem when audio open
  - samples: power_mode_switch: fix hpm62xx/63xx/67xx into shutdown mode can't be woke up
  - samples: i2s: fix pdm record data buff size according board
  - samples: lwip_ptp: v1 & v2: fix compiling error with gnu gcc toochain in v13.0
  - samples: i2s_emulation: fixed build error for nds gcc
  - samples: drivers: spi: interrupt: Abnormal working for IAR release build
  - samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
  - samples: drivers: spi: dma: master: fixed can not work sometimes with release build issue
  - samples: i2s_emulation: fixed can not stop when playing issue
  - samples: drivers: gptmr: opmode:  fixed can not work with  release build type
  - samples: dsp: Calculation error in dsp demo.
  - samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
  - samples: drivers: uart: uart_hardware_rx_idle: fiexd can not work with zcc release build type
  - samples: bldc offline detection: fix release run error.
  - samples: mono: fix value get logic on zcc.
  - samples: fix sample slave tamagawa's trx error handling method
  - samples: ecat: fix build ZCC error
  - samples: lower power: hpm6300 and hpm6700 can't use pcfg_dcdc_set_current_hys_range() API
  - cmake: ide: correct glob source adding
  - cmake: zcc: correct arch setting to enable dsp
  - scripts: add errors=ignore and encode=utf8 parameters to avoid python unicode build error.
  - samples: motor_ctrl: bldc_xxx & step_motor_foc: add missing diff_sel passed into adc12_init()
  - samples: ethercat: ecat_cia402: motor: bldc_foc: add missing diff_sel passed into adc12_init()
  - samples: drivers: adc: adc12: add missing diff_sel passed into adc12_int()
  - doc: fix threadx doc title

- Added:
  - soc: HPM6300: add pps1_en
  - drivers: add hrpwm recovery method.
  - drivers: trgmux: add hrpwm calibration driver.
  - drivers: sei: add sei_set_dma_req_enable() API
  - drivers: ppi: add and use ppi_ns2cycle() API
  - drivers: i2c: add I2C_WRITE_CHECK_ACK flag  for i2c_master_transfer API
  - drivers: i2c: add i2c_master_seq_transmit API
  - drivers: plb: add new plb interface
  - drivers: tsw: add tas, cbs and pps APIs
  - drivers: tsw: add tx-timestamp-fifo APIs
  - components: tsw_phy add RTL8211 and JL1111 drivers
  - components: add pmbus
  - components: ppi: add README.md docs
  - components: add plb abz encoder.
  - middleware: add hpmicro monitor.
  - middleware: motor_ctrl: add motor parameter detection.
  - middleware: add tsn
  - samples: tsn: add lwip_tcpecho
  - samples: bldc_foc: add motor monitor demo.
  - samples: motor_ctrl: add bldc parameter detection demo.
  - samples: drivers: pwmv2: add hrpwm calibration demo.
  - samples: cherryusb: add mouse remote wakeup sample
  - samples: gptmr: add opmode/monitor/cntmode sample
  - samples: add pmbus samples
  - samples: cherryusb: dual_host: support two msc device
  - samples: ecat: add ecat_foe samples
  - samples: ecat: add ecat_cia402 samples
  - samples: ecat: add ecat_foe driver
  - samples: ecat: update hpm_ecat_hw driver
  - samples: drivers: enet: add pps_capture sample
  - samples: add plb encoder demo.
  - samples: tsn: add tsn_time_aware_scheduling
  - samples: tsn: add tsn_ptp_freertos(master&slave)
  - samples: tsn: add tsn_credit_based_shaper
  - samples：ecat_cia402: add virtual motor support

Signed-off-by: Ryan QIAN <[email protected]>
  • Loading branch information
@jhqian
jhqian committed Sep 30, 2024
1 parent 44d8bcd commit 276af93
Show file tree
Hide file tree
Showing 1,049 changed files with 57,808 additions and 10,149 deletions.
241 changes: 240 additions & 1 deletion CHANGELOG.md
View file
Original file line number Diff line number Diff line change
@@ -1,5 +1,245 @@
# Change Log

## [1.7.0] - 2024-09-30:

Main changes since 1.6.0
Tested Segger Embedded Studio Version: 8.16a
Tested Zcc toolchain 3.2.4

### Changed:
- soc: HPM6E00: HPM6E80: add tsw section
- soc: add hpm_otp_table.h
- soc: enet: add a macro for DMA bus width
- soc: system.c: set bpor.por_confing retention bit to avoid bgpr data loss
- soc: pcfg: add pcfg_wakeup_src_t enum and pcfg_update_periph_clock_mode API
- soc: hpm5300: exclude fgpio region from dlm
- soc: add CONFIG_ENABLE_BPOR_RETENTION macro to control bpor retention
- soc: linker: icf: update cherryusb_usbh_class_info section placement
- soc: HPM6300/HPM6700: delete pcfg_dcdc_set_current_hys_range() API
- ip: i2s: add and use clk_i2s_src_audn instead of clk_i2s_src_aud0/1/2/3
- boards: remove hpm6750evk support
- boards: hpm6e00evk: update femc pinmux
- boards: pinmux: set max frequency slew rate for SPI GPIO
- boards: hpm5301evklite: Change cap1 and comp1 pins of gptmr0
- boards: hpm5301evklite: change i2c2 to i2c3 for BOARD_APP_I2C
- boards: add board_init_gptmr_channel_pin API for all board
- boards: hpm6e00evk: update core1 debugger console readme
- boards: all: add board_init_acmp_pins API
- boards: hpm6800evk: adc16: update clock bus name for clock initialization
- boards: adc16: rename api parameter clk_src_ahb to clk_src_bus
- boards: add BOARD_APP_ADC16_CLK_BUS definition
- boards: hpm6e00evk: update board readme
- boards: hpm6e00evk: bump up DCDC voltage to 1250mv
- boards: add enet pps input feature and pinmux setting API
- boards: add missing board feature and pin descriptions for enet pps output pin
- boards: xxxx.yaml: rename board feature name related to enet pps pin
- boards: add BOARD_MASTER_I2S and BOARD_SLAVE_I2S
- boards: add board mic and speaker i2s definition
- boards: doc: pwm: add pwm pin descriptions.
- boards: hpm6800evk reduce ddr io leakage.
- boards: hpm6800evk: pps: adjust pinmux settings
- drivers: tsw: optimize the logic of sending and receiving APIs
- drivers: tsw: add APIs for speed, interface, and clock delay settings
- drivers: tsw: split tsw_ep_enable_mac_ctrl API to two APIs for enableing and disabling
- drivers: usb: update usb phy init for suspend
- drivers: qeiv2: update comments
- drivers: i2c: auto ack needs to be enabled after the transmission is completed for i2c_master_transfer API
- drivers: adc16: split adc16_set_pmt_queue_enable() into enable and disable API
- drivers: gptmr: add opmode cntmode monitor configuration member for gptmr_channel_config API
- drivers: spi: add the judgment that the frequency ratio cannot be greater than 510 for spi_master_timing_init API
- drivers: enet: add retry logic in DMA initialization
- drivers: spi: Add slave mode judgment for spi_control_init API
- drivers: spi: add spi busy state judement for transfer APIs
- drivers: uart: add disable rx timeout trigger dma function
- drivers: i2s: add buff data align with frame feature
- drivers: acmp: add acmp_channel_config_cap_selection
- drivers: acmp: update acmp_channel_config_dac API
- drivers: usb: update usb phy init and deinit
- drivers: enet: add auxiliary snapshot APIs and struct definitions
- drivers: usb: update usb_force_port_resume() annd add usb_hcd_disable_ase_pse() APIs
- drivers: tsw: update the prefix of apis starting with tsn to tsw
- drivers: qeiv2: update qeiv2_config_adcx_adcy_param()
- drivers: usb: update usb_hcd_disable_ase_pse() & usb_hcd_enable_ase_pse()
- components: enet_phy: rtl8211: optimize logic for initialization config
- components: ppi: add assert check for cs_index and cmd_start_index
- components: ppi: update AD-MUX mode config to decrease address latch
- components: smbus: i2c_master_write replaces i2c_master_transfer for all smbus write APIs
- components: serial_nor: Added configuration return judgment for transfer API
- components: serial_nor: judge DMA sending completion for hpm_spi_transfer_via_dma API
- components: spi: add spi busy state judgment for hpm_spi_transfer_init API
- components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_buffer_nonblocking API
- components: i2s_over_spi: optimized hpm_i2s_master_over_spi_tx_stop API
- components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_is_busy API
- middleware: hpm_math: support zcc new version
- middleware: cherryusb: update to v1.4.0
- middleware: lwip: CMakeLists.txt: add cmake flag for apps
- middleware: cherryusb: don't clean csc bit when init
- middleware: cherryusb: msc host: support multi msc device
- middleware: fatfs: cherryusb: support two msc device
- middleware: reduce netx mem usage
- middleware: cherryusb: host: update usb_hc_deinit()
- middleware: usbx: host: delete mode setting in usb_host_mode_init()
- middleware: hpm_sdmmc: sdcard: added retransmission to improve SPI SD card compatibility
- middleware: tinyengine: rename old function
- samples: audio_codec: change default codec setting in CMakeLists.txt
- samples: adc16 & motor_ctrl: update adc16 preemption queue enable control APIs
- samples: ppi: parallel_adc: update function name
- samples: ppi: async_sram: update to support AD Mux Mode
- samples: lwip & modbus: add judgement for the return value of enet controller initialization
- samples: lwip: lwip_iperf: exclude flahsh_uf2 & flash_uf2_release targets
- samples: lwip: add conditional compilation for RMII port
- samples: cherryusb: msc host: adapter to fatfs update
- samples: drivers: acmp: replace init_acmp_pins API with board_init_acmp_pins API
- samples: ecat: read mailbox ram buff by ram alias address
- samples: ecat: set PHY offset
- samples: ecat_phy: disable PHY addr 00 broadcast response
- samples: drivers: adc16: reference APP_ADC16_CLOCK_BUS instead of clk_adc_src_ahb0
- samples: ecat_io: update flash_eeprom data address
- samples: ecat: update SSC config xml and ESI xml
- samples: lwip: ports: rtthread-nano: single&multiple: add sys_arch_protech()/sys_arch_unprotect()
- samples: power_mode_switch: move sysctl_enable_cpu0_wakeup_source_with_irq() to stop mode settings
- samples: power_mode_switch: keep puart clock and wakeup enable visible
- samples: acmp: add a macro TEST_ACMP_DAC_MAX_VALUE for better compatibility
- samples: drivers: enet: pps: app.yaml: rename dependency
- samples: ppi: parallel_adc: use macro BOARD_PPI_ADC_CS_INDEX
- samples: i2s: use BOARD_MASTER_I2S and BOARD_SLAVE_I2S
- samples: audio_codec: use board speaker macros
- samples: cherryusb: audio: use board mic and speaker macros
- samples: lwip & cherryusb/host/usbnet: use the external struct timeval definition from compile system
- samples: esc: update esc read to 32bit access
- samples: ecat_foe: update log and README
- samples: ecat_foe: foe flash read cache maintenance
- samples: ppi: use macros to select pins
- samples: drivers: gptmr: cntmode: volatile to key parameter variables to prevent them from being optimized
- samples: spi_sdcard: Added delay function registration
- samples: cherryusb: mouse_wakeup: update printf log
- samples: cherryusb: midi: update readme
- samples: i2s: change HDMA to XDMA
- samples: tflm: optimized speed.
- samples: tflm: add zcc compile options.
- samples: spi_component: full_duplex: Add known issues in the master readme
- samples: spi_components: half_duplex: reduce SPI SCLK frequency to adapt to different slave boards
- samples: spi_components: full_duplex: reduce SPI SCLK frequency to adapt to different slave boards

### Fixed:
- soc: HPM6800: HPM6880: fix the clock bus name for wdg
- soc: SPI_SOC_TRANSFER_COUNT_MAX Definition error for HPM6E00
- soc: preserve kept symbols while -flto is enabled
- soc: hpm6880: fix clk bus name for adc from ahb0 to axis0
- soc: HPM6300: fix get get_frequency_for_i2s_or_adc() problem
- soc: HPM6700: fix clock_set_i2s_source() check condition
- soc: romapi: Fix unexpected data fetch error during flash init/write.
- soc: linker: gcc: fix fast_ram postion
- boards: hpm5301evklite: add a missing macro BOARD_APP_ADC16_CLK_BUS
- boards: i2c init: clock_add_to_group() should be before board_i2c_bus_clear()
- boards: hpm6800evk pinmux PRS set wrong value
- boards: hpm6750evkmini: fixed the iomux errata causes the slave to not work issue
- boards: hpm6750evk2: fixed the iomux errata causes the slave to not work issue
- boards: hpm6750evkmini: add the missing implement of enabling enet irq
- boards: hpm6750evkmini: fix touch reset timing.
- drivers: i2c: correct API name
- drivers: gptmr: fix cmp value can't set 0xFFFFFFFF problem
- drivers: pwmv2: fix counter burst set error.
- drivers: enet: fix return value of enet_dma_init()
- drivers: usb: fix usb_dcd_remote_wakeup() api
- drivers: enet: fix enet max frame size
- drivers: spi: Fixed mode variable assignment error for spi_slave_get_default_format_config API
- drivers: i2s: fix fill dummy data in slave mode
- drivers: adc16: fix ADC16 conversion results in single-ended mode
- drivers: enet: fix that TSIS interrupt is disabled by default
- drivers: femc: fix cmd_data_width comment error
- drivers: spi: fixed offset digit error problem for spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
- drivers: spi: fixed possible packet loss during reception for spi_read_data API
- drivers: usb: fix phy init for host
- drivers: touch: gtxx: fix reset timing
- drivers: mipi dsi: fix bandwidth low
- drivers: mcan: fix wrong offset in can_rx_message_t.
- drivers: adc12: fix using a wrong calibration value
- components: ppi: fix config variable init value
- components: serial_nor: Fixed the nonblock APIs naming error
- components: serial_nor: spi: fixed formating issue for write API
- components: eeprom_emulation, add "fence.i" after nor_flash init
- components: spi: fixed the waring of no return value for hpm_spi_transfer_init API
- middleware: fix Nan calculation error.
- middleware: lwip: apps: lwiperf: fix the type of clk_id from int to clockid_t
- middleware: fix tickless mode cannot work
- middleware: eclipse_threadx: netxduo: fix confilicting types for 'enet_mask_interrupt_event'
- middleware: tinyengine: zcc compile error.
- middleware: cherryusb: fix msc class miss return
- middleware: motor_monitor: fix nds toolchain error
- middleware: hpm_mcl: pwm output exception.
- samples: sdm: correct gptmr trigger time
- samples: gptmr: cmp0 and cmp1 should be setting together
- samples: i2s_emulation: fixed playback is not actually stopped issue
- samples: pwmv2: fix pwm period error.
- samples: drivers: dac: fix output stop after restart in buffer mode
- samples: fatfs: fix driver_num_buf don't have EOF
- samples: dac: buffer mode: fix DAC output of negative narrow pulse nearly to zero at the top of sinewave
- samples: lwip: fix enet receive buffer size setting
- samples: lwip: fix some memroy-related issues when using socket/netcon API
- samples: cherryusb: audio: fix mute problem when audio open
- samples: power_mode_switch: fix hpm62xx/63xx/67xx into shutdown mode can't be woke up
- samples: i2s: fix pdm record data buff size according board
- samples: lwip_ptp: v1 & v2: fix compiling error with gnu gcc toochain in v13.0
- samples: i2s_emulation: fixed build error for nds gcc
- samples: drivers: spi: interrupt: Abnormal working for IAR release build
- samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
- samples: drivers: spi: dma: master: fixed can not work sometimes with release build issue
- samples: i2s_emulation: fixed can not stop when playing issue
- samples: drivers: gptmr: opmode: fixed can not work with release build type
- samples: dsp: Calculation error in dsp demo.
- samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
- samples: drivers: uart: uart_hardware_rx_idle: fiexd can not work with zcc release build type
- samples: bldc offline detection: fix release run error.
- samples: mono: fix value get logic on zcc.
- samples: fix sample slave tamagawa's trx error handling method
- samples: ecat: fix build ZCC error
- samples: lower power: hpm6300 and hpm6700 can't use pcfg_dcdc_set_current_hys_range() API
- cmake: ide: correct glob source adding
- cmake: zcc: correct arch setting to enable dsp
- scripts: add errors=ignore and encode=utf8 parameters to avoid python unicode build error.
- samples: motor_ctrl: bldc_xxx & step_motor_foc: add missing diff_sel passed into adc12_init()
- samples: ethercat: ecat_cia402: motor: bldc_foc: add missing diff_sel passed into adc12_init()
- samples: drivers: adc: adc12: add missing diff_sel passed into adc12_int()
- doc: fix threadx doc title

### Added:
- soc: HPM6300: add pps1_en
- drivers: add hrpwm recovery method.
- drivers: trgmux: add hrpwm calibration driver.
- drivers: sei: add sei_set_dma_req_enable() API
- drivers: ppi: add and use ppi_ns2cycle() API
- drivers: i2c: add I2C_WRITE_CHECK_ACK flag for i2c_master_transfer API
- drivers: i2c: add i2c_master_seq_transmit API
- drivers: plb: add new plb interface
- drivers: tsw: add tas, cbs and pps APIs
- drivers: tsw: add tx-timestamp-fifo APIs
- components: tsw_phy add RTL8211 and JL1111 drivers
- components: add pmbus
- components: ppi: add README.md docs
- components: add plb abz encoder.
- middleware: add hpmicro monitor.
- middleware: motor_ctrl: add motor parameter detection.
- middleware: add tsn
- samples: tsn: add lwip_tcpecho
- samples: bldc_foc: add motor monitor demo.
- samples: motor_ctrl: add bldc parameter detection demo.
- samples: drivers: pwmv2: add hrpwm calibration demo.
- samples: cherryusb: add mouse remote wakeup sample
- samples: gptmr: add opmode/monitor/cntmode sample
- samples: add pmbus samples
- samples: cherryusb: dual_host: support two msc device
- samples: ecat: add ecat_foe samples
- samples: ecat: add ecat_cia402 samples
- samples: ecat: add ecat_foe driver
- samples: ecat: update hpm_ecat_hw driver
- samples: drivers: enet: add pps_capture sample
- samples: add plb encoder demo.
- samples: tsn: add tsn_time_aware_scheduling
- samples: tsn: add tsn_ptp_freertos(master&slave)
- samples: tsn: add tsn_credit_based_shaper
- samples：ecat_cia402: add virtual motor support

## [1.6.0] - 2024-06-28:

Main changes since 1.5.0
Expand Down Expand Up @@ -1516,4 +1756,3 @@ All changes since 0.6.2
- samples: drivers: gpiom: Add example to demonstrate gpiom's function
- drivers: common: add macro to put data into noncacheable sections
- middleware: integrate lwip

1 change: 1 addition & 0 deletions README.md
View file
Original file line number Diff line number Diff line change
Expand Up @@ -43,6 +43,7 @@ The HPM SDK Project is a software development kit based on HPMicro's MCUs, which
## Repositories
- hpm_sdk: https://github.com/hpmicro/hpm_sdk
- sdk_env: https://github.com/hpmicro/sdk_env
- hpm_apps: https://github.com/hpmicro/hpm_apps
- sdk extra demo: https://github.com/hpmicro/hpm_sdk_extra
- openocd (hpmicro patched): https://github.com/hpmicro/riscv-openocd
- gnu gcc toolchain: https://github.com/hpmicro/riscv-gnu-toolchain
Expand Down
2 changes: 1 addition & 1 deletion VERSION
View file
Original file line number Diff line number Diff line change
@@ -1,5 +1,5 @@
VERSION_MAJOR = 1
VERSION_MINOR = 6
VERSION_MINOR = 7
PATCHLEVEL = 0
VERSION_TWEAK = 0
EXTRAVERSION = 0
30 changes: 21 additions & 9 deletions boards/hpm5300evk/board.c
View file
Original file line number Diff line number Diff line change
@@ -1,5 +1,5 @@
/*
* Copyright (c) 2023 HPMicro
* Copyright (c) 2023-2024 HPMicro
* SPDX-License-Identifier: BSD-3-Clause
*
*/
Expand Down Expand Up @@ -71,11 +71,11 @@ static board_timer_cb timer_cb;
* 0 - 4MB / 1 - 8MB / 2 - 16MB
*/
#if defined(FLASH_XIP) && FLASH_XIP
__attribute__ ((section(".nor_cfg_option"))) const uint32_t option[4] = {0xfcf90002, 0x00000006, 0x1000, 0x0};
__attribute__ ((section(".nor_cfg_option"), used)) const uint32_t option[4] = {0xfcf90002, 0x00000006, 0x1000, 0x0};
#endif

#if defined(FLASH_UF2) && FLASH_UF2
ATTR_PLACE_AT(".uf2_signature") const uint32_t uf2_signature = BOARD_UF2_SIGNATURE;
ATTR_PLACE_AT(".uf2_signature") __attribute__((used)) const uint32_t uf2_signature = BOARD_UF2_SIGNATURE;
#endif

void board_init_console(void)
Expand Down Expand Up @@ -389,12 +389,12 @@ void board_usb_vbus_ctrl(uint8_t usb_index, uint8_t level)
(void) level;
}

uint32_t board_init_adc_clock(void *ptr, bool clk_src_ahb)
uint32_t board_init_adc_clock(void *ptr, bool clk_src_bus)
{
uint32_t freq = 0;

if (ptr == (void *)HPM_ADC0) {
if (clk_src_ahb) {
if (clk_src_bus) {
/* Configure the ADC clock from AHB (@200MHz by default)*/
clock_set_adc_source(clock_adc0, clk_adc_src_ahb0);
} else {
Expand All @@ -405,7 +405,7 @@ uint32_t board_init_adc_clock(void *ptr, bool clk_src_ahb)

freq = clock_get_frequency(clock_adc0);
} else if (ptr == (void *)HPM_ADC1) {
if (clk_src_ahb) {
if (clk_src_bus) {
/* Configure the ADC clock from AHB (@200MHz by default)*/
clock_set_adc_source(clock_adc1, clk_adc_src_ahb0);
} else {
Expand All @@ -425,6 +425,10 @@ void board_init_adc16_pins(void)
init_adc_pins();
}

void board_init_acmp_pins(void)
{
init_acmp_pins();
}
uint32_t board_init_dac_clock(DAC_Type *ptr, bool clk_src_ahb)
{
uint32_t freq = 0;
Expand Down Expand Up @@ -563,7 +567,7 @@ void board_i2c_bus_clear(I2C_Type *ptr)
printf("I2C bus is ready\n");
return;
}
i2s_gen_reset_signal(ptr, 9);
i2c_gen_reset_signal(ptr, 9);
board_delay_ms(100);
printf("I2C bus is cleared\n");
}
Expand All @@ -576,13 +580,15 @@ void board_init_i2c(I2C_Type *ptr)
if (ptr == NULL) {
return;
}
init_i2c_pins(ptr);
board_i2c_bus_clear(ptr);

clock_add_to_group(clock_i2c0, 0);
clock_add_to_group(clock_i2c1, 0);
clock_add_to_group(clock_i2c2, 0);
clock_add_to_group(clock_i2c3, 0);

init_i2c_pins(ptr);
board_i2c_bus_clear(ptr);

/* Configure the I2C clock to 24MHz */
clock_set_source_divider(BOARD_APP_I2C_CLK_NAME, clk_src_osc24m, 1U);

Expand Down Expand Up @@ -614,3 +620,9 @@ void board_lin_transceiver_control(bool enable)
gpio_set_pin_output_with_initial(BOARD_LIN_TRANSCEIVER_GPIO_CTRL, BOARD_LIN_TRANSCEIVER_GPIO_INDEX, BOARD_LIN_TRANSCEIVER_GPIO_PIN, 0); /* enable transceiver sleep */
}
}

void board_init_gptmr_channel_pin(GPTMR_Type *ptr, uint32_t channel, bool as_comp)
{
init_gptmr_channel_pin(ptr, channel, as_comp);
}

Loading

0 comments on commit 276af93

Please sign in to comment.