Skip to content

8‐2 Add Commands_jp

Jump to bottom
Yusuke Ogawa edited this page Oct 3, 2025 · 16 revisions

Masterファイルを直接編集するため、実行前に必ずMasterファイルをバックアップしてください。

本手順でできること

CLIから以下のaddコマンドを実行できます

基本構文

python [file path]/network_sketcher.py [command] --master [master file path]
  • 以下のように[command] 、--master [master file path]　の場所は変更可能
    python [file path]/network_sketcher.py -master [master file path] [command]

add ip_address

レイヤ３インタフェースにIPアドレスを作成します。１回に１つのIPアドレスが作成できます。繰り返すことで複数のIPアドレスの追加が可能です。

python [file path]/network_sketcher.py add ip_address [device name] [layer3_portname] [ip_address/subnetmask] --master [master file path]
  • ex.

+BEFORE+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 100', '', '']

+IP Address added+
＃python .\network_sketcher.py add ip_address 'L3SW2' 'Vlan 100' '192.168.100.100/24' --master "C:\work\[MASTER]test.xlsx"
--- IP Address added --- L3SW2,Vlan 100,192.168.100.100/24

+AFTER+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 100', '', '192.168.100.100/24']

add l2_segment

インタフェースにVLAN等のレイヤ２セグメントを作成します。１回に１つのレイヤ２セグメントが作成できます。複数のレイヤ２セグメントの作成が可能です。

python [file path]/network_sketcher.py add ip_address [device name] [layer2_portname] [l2segment_name]　--master [master file path]
  • ex.

+BEFORE+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'GigabitEthernet 0/0', '', 'Vlan100,Vlan200,Vlan300', '']

+l2_segment added+
＃python .\network_sketcher.py add l2_segment 'L3SW2' 'GigabitEthernet 0/0' 'addvlan999' --master "C:\work\[MASTER]test.xlsx"
--- l2 Segment added --- L3SW2,GigabitEthernet 0/0,addvlan999

+AFTER+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'GigabitEthernet 0/0', '', 'Vlan100,Vlan200,Vlan300,addvlan999', '']

add virtual_port

VLANインタフェース(SVI)等のレイヤ３インタフェースを作成します。

python [file path]/network_sketcher.py add virtual_port [device name] [virtual_portname] --master [master file path]
  • ex.

+BEFORE+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', '', 'Vlan 300', 'Vlan300', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 300', '', '']

+virtual_port added+
＃python .\network_sketcher.py add l2_segment 'L3SW2' 'GigabitEthernet 0/0' 'addvlan999' --master "C:\work\[MASTER]test.xlsx"
--- Virtual Port added --- L3SW2,addvlan 999

+AFTER+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', '', 'addvlan 999', '', '']
['L3SW2', '', 'Vlan 100', 'Vlan100', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 300', '', '']
['L3SW2', 'addvlan 999', '', '']

Author

  • Yusuke Ogawa - Security Architect, Cisco | CCIE#17583

License

SPDX-License-Identifier: Apache-2.0

Copyright 2023 Cisco Systems, Inc. and its affiliates

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Clone this wiki locally