@@ -2,66 +2,66 @@
 title: M-1 LED Matrix Creating Your Own GIF
 description: Step by step guide to adding a GIF to the M-1 LED Matrix!
 ---
-1. Make sure you know your Apollo M-1 board revision (look on the back of the controller), Rev 4 or Rev 6, and are on firmware version 14.5.1. You can flash your device [here](https://wiki.apolloautomation.com/products/m1/troubleshooting/m1-reflash/).
-2. Select Config
+1. Make sure you know your Apollo M-1 board revision (look on the back of the controller), Rev 4 or Rev 6, and are on firmware version 14.5.1. You can flash your device [here](https://wiki.apolloautomation.com/products/m1/troubleshooting/m1-reflash/). Also, make sure you have the correct LED matrix settings [here](https://wiki.apolloautomation.com/products/m1/setup/m1-matrix-settings/).
+2. Connect to the Apollo M-1 Wi-Fi hot spot and it should take you directly to the main dashboard. Then select Config.
 3. ![](../../../assets/config.png)
-4. Select Wi-Fi Setup
+4. Select Wi-Fi Setup.
 
    ![](../../../assets/wifi.png)
 
-5. Add your M-1 to your Wi-Fi network by selecting Scan and adding your Wi-Fi credentials
+5. Add your M-1 to your Wi-Fi network by selecting Scan and adding your Wi-Fi credentials.
 
    ![](../../../assets/ssid.png)
 
-6. Now you can grab the IP address of the M-1 from your router which should be labeled esp32s3
+6. Now you can grab the IP address of the M-1 from your router which should be labeled esp32s3.
 
    ![](../../../assets/esp.png)
 
-7. Copy the IP address and paste it into the URL bar of your browser
+7. Copy the IP address and paste it into the URL bar of your browser. This will take you to the Apollo M-1 dashboard.
 
    ![](../../../assets/ip.png)
 
-8. Now find your GIFof choice
+8. Now find your GIF of choice and save it to your computer.
 
    ![](../../../assets/gsd.gif)
 
-9. Now we need to go to [https://ezgif.com/](https://ezgif.com/) and select Resize
+9. Now we need to go to [https://ezgif.com/](https://ezgif.com/) and select Resize.
 
    ![](../../../assets/resize.png)
 
-10. Select Browse and Upload your GIF
+10. Select Browse and Upload your GIF.
 
     ![](../../../assets/upload-gif.png)
 
-11. Change the Width and Height to 64x64, select resize and save the GIF (use an easy name since we will be using it later)
+11. Change the Width and Height to 64x64, select resize and save the GIF (use an easy name since we will be using it later).
 
     ![](../../../assets/64x64-1.png)
 
-12. Now go back to the Apollo M-1 IP address and select config
+12. Now go back to the Apollo M-1 IP address and select config.
 
     ![](../../../assets/config-1.png)
 
-13. Select File System
+13. Select File System.
 
     ![](../../../assets/file-system.png)
 
-14. Select Browse, choose your GIF and then select Upload
+14. Select Browse, choose your GIF and then select Upload.
 
     ![](../../../assets/upload.png)
 
-15. Now go back to your Apollo M-1 IP address, select the Image effect, use the pencil to rename the effect EXACTLY the same as your GIF (example: gsd.gif) and select the check mark to save it
+15. Now go back to your Apollo M-1 IP address, select the Image effect, use the pencil to rename the effect EXACTLY the same as your GIF file (example: gsd.gif) and select the check mark to save it.
 
     ![](../../../assets/image-8.png)
 
 16. Now you should see your GIF playing on the Apollo M-1!
 
     ![](../../../assets/panel.png)
 
-17. Not finished yet though! Select Preset, type in a name and save it to the device
+17. Not finished yet though! Select Preset, type in a name and save it to the device.
 
     ![](../../../assets/save.png)
 
-18. Now you can play it whenever you would like and you can even set it as the boot effect (Config &gt; LED Preferences &gt; Change Apply Preset to the preset number you just made)
+18. Now you can play it whenever you would like and you can even set it as the boot effect (Config &gt; LED Preferences &gt; Change Apply Preset to the preset number you just made).
 
     ![](../../../assets/boot.png)